PLEASE READ THIS FIRST !

Oh no! You've dropped your digital stuff. And it's out of warranty. And repair costs more than the digital stuff is worth. What to do short of tossing the digital stuff (or selling on ebay)? Well, believe it or not the average person has a good chance of diy fixing that digital stuff themselves. All they'll need for most cases is some patience, and a little background knowledge. The intent of the posts on this blog are to help provide that knowledge.

Disclaimer Warning: The following instructions are given without any warranty. They don't have to be complete or correct. Don't do any of the following steps if you're not sure of what you're doing. You could damage your digital stuffs and you WILL lose your warranty. Everything you do will be at your own risk.

Disclaimer Notice : imprtant things to know before you start taking Part your digital stuffs

Showing posts with label iPhone. Show all posts
Showing posts with label iPhone. Show all posts

Wednesday, August 19, 2009

How to unlock the iPhone 3G

How to unlock the iPhone 3G
Tools You'll Need: iPhone 3G , TurboSIM Card

Upon completion of these steps, you will be able to unlock and use your iPhone 3G with any wireless network carrier with your existing SIM card


1 - Locate and acquire a TurboSim unlock card. These can be found on eBay by conducting a search for 'turbo sim'. They can be purchased for around $10.
2 - Once you've received your TurboSIM card, locate the SIM Card slot at the top of your iPhone. To open the slot and remove the SIM card, use a paper clip to push the small button inside the hole on the SIM card cradle. The cradle will release and pop out.
3 - Place the TurboSIM card inside the SIM card cradle. Be sure to place it in the cradle so it is oriented the same as the SIM card that was removed.
4 - Place your new (or old) SIM card from any wireless carrier on top of the TurboSIM card so that the 6 leads that protrude make contact with the conductors on the new/old SIM card. This may require a small cut on the corner of your SIM card to make room for the chip on the TurboSIM card depending on which version you purchase. If you must make the cut, it is not a big deal since it is on the side where it is only plastic.
5 - Carefully place the SIM and TurboSIM sandwich back inside your iPhone. When your turn your iPhone back on, it will tell you that you have no service. Wait a couple of minutes and let the TurboSIM do its job. After the couple of minutes, the message will go away and you'll be making calls on whatever wireless carrier you choose!

How to Disassemble IPhone 3G

How to Disassemble IPhone 3G
Tools You'll Need: Small Phillips Screw Driver , Small Flathead or exacto razor , Safe Open Tool

Ever wonder how to Disassemble your IPhone, or you really need to know how to open it because you need to replace the LCD screen because your screen cracked and. We all know it is cheaper to replace the screen than to by a new phone. Well Don't worry, here is your solution in this article you will learn how to disassemble your Iphone so you can fix it

This Article will show you how to open your IPhone3G

Remove the sim tray, use the included sim card removal tool (or a paper clip if you've lost the tool.)

Holding your device on end you will notice two small screws on either side of the dock. These screws must be removed in order to open the case.

Insert a small thin tool between the chrome ring and front panel glass directly above one of the screw holes. You will need to exert a small amount of pressure to separate the display from the back panel

Lift the panel up from the dock end being careful not to tear or break any ribbons connected near the other end.

Unplug ribbons 1 and 2 by lifting them from the main board. Under ribbon 2 you will need to find and unclip ribbon 3, then carefully remove the display assembly.

Remove the seven screws circled in red. Note: One screw is located under the DO NOT REMOVE sticker.

Unplug ribbon 4.

Lift the mother board out taking note of the camera which is still connected to the underside of the board. You will need to unplug the ribbon circled in red.

Place the mother board to the side

Use the attached tab to pull up on the battery, there is a mild adhesive on the back side, so it will take a bit of force.

Remove the screw circled in red.

Carefully remove the camera

Remove the nine screws circled in red.

Remove the headphone jack and attached flex cable.

Remove the speaker assembly which also contains the dock connector, antennae and home button as well.

Remove the 2 screws circled in red.

Place the ######## assembly to the side

Remove the 2 screws circled in red. You will find 3 screws on the opposite side which must be removed as well.

Lift the LCD free from the front panel glass.

Pictured is every component inside the iPhone 3G.You did it!

Wednesday, July 29, 2009

Apple iPhone 3G disassembly

Apple iPhone 3G disassembly
Tools required: Phillips size 0 screwdriver, plastic tool such as a guitar plectrum or credit card, needle/drawing pin/paperclip or something similar.

With your phone upright, push something like a paperclip into the hole at the top of the phone. This will release the sim holder.

With the sim holder released, your phone will look like below.

Remove the two screws at the other end of the phone.

Use your plastic tool to lever the phone apart slightly.

The edge of the screen should now be raised slightly and you can lift it up.

Lift the screen up to access a number of ribbon connectors. Each one attaches like a plug and socket. Just lever the two circled connectors up to unplug them.

The next ribbon connector (circled) has a black latch that you flick up to release the ribbon. You can then lift the LCD away from the phone.

Your phone should now look like below.

Remove the screws on each side of the screen.

The screws on the other side will be covered by a piece of sticky tape which you'll need to peel back.

Now remove the screw circled below.

Slide your plastic tool under the LCD screen to release it.

You should now have the LCD screen removed. Reverse the whole procedure for reassembly..

apple iPhone disassembly

apple iPhone disassembly

Tools required: iPhone opening tool, Phillips size 0 screwdriver, needle/drawing pin/paperclip or something similar

First remove the sim holder. To do this, push something like a needle into the small hole at the top of the phone. Push down and the sim holder will pop up.

The sim holder should now be removed.

Use the opening tool, or something strong with a thin edge (something plastic is best because a metal tool will damage the case), to pull the antenna cover off in the direction of the arrows. Some force is required.

You should now have the antenna cover removed.

Remove the three screws, circled below.

Run your opening tool around the join of the back cover. Some force is required.

The back cover should now be loose. Carefully lift it away from the phone. It will still be connected by a ribbon cable. The connector (circled) attaches like a plug and socket. Lift it up and it will unplug.

You should now have the back cover removed. Now remove ten screws around the outside edge of the phone.

With the ten screws removed you can remove the silver bezel, as shown below.

Your phone should now look like below. Three more connectors need to be disconnected (circled). Do so by using pushing a small screwdriver underneath then levering them off. Remove the three screws, indicated by the arrows.

Now pull the circuit board away, like below. It'll still be connected by some more wires so don't try and remove it completely. The battery now needs removing. It is held in place by some very tacky glue. You need to try and slide something underneath the battery to lever is out. An old credit card cut in half should do the job

Your phone should now look like below. The battery and circuit board should still be connected to each other. You'll notice that four connectors (circled) disconnected when you removed the circuit board.

Lever out the mic, shown below.

The LCD screen and digitiser (touch screen) are held on by three clips on each side. Lever the metal clips back slightly.

The LCD screen and digitiser are still held in place with tacky glue at the top and bottom. If possible, use a hair dryer to heat the glue up to make it easier the remove the screen. Then push something like a credit card in between the screen and the rest of the phone to help release the screen. Once the screen is loose, turn the phone over and you'll notice a few ribbon coming away with it. Ease these through the back of the phone so that they don't get damaged.

You should now have the LCD screen and digitiser removed. Reverse the whole procedure for reassembly.