PLEASE READ THIS FIRST !

Oh no! You've dropped your digital stuff. And it's out of warranty. And repair costs more than the digital stuff is worth. What to do short of tossing the digital stuff (or selling on ebay)? Well, believe it or not the average person has a good chance of diy fixing that digital stuff themselves. All they'll need for most cases is some patience, and a little background knowledge. The intent of the posts on this blog are to help provide that knowledge.

Disclaimer Warning: The following instructions are given without any warranty. They don't have to be complete or correct. Don't do any of the following steps if you're not sure of what you're doing. You could damage your digital stuffs and you WILL lose your warranty. Everything you do will be at your own risk.

Disclaimer Notice : imprtant things to know before you start taking Part your digital stuffs

Showing posts with label Headphone. Show all posts
Showing posts with label Headphone. Show all posts

Sunday, September 27, 2009

Installing iPod 5th Generation (Video) Headphone Jack and Hold Switch

Installing iPod 5th Generation (Video) Headphone Jack and Hold Switch

Instructions on how to remove the headphone jack from the 5th Gen iPod Video.

Tools used in this guide : Phillips #00 Screwdriver , iPod Opening Tools
Parts relevant to this guide : iPod Video 30 GB Headphone Jack & Hold Switch , iPod Video 60/80 GB Headphone Jack & Hold Switch

Step 1 — Case
Before opening your iPod, ensure that the hold switch is in the locked position. The slider should be all the way to the right if your iPod is facing you.

Step 2
Opening the iPod can be challenging. Do not get discouraged if it takes you a few tries before the iPod is opened.

Free the first retainer clip on the bottom of the iPod using the large iPod opening tool. The tool's edge should point towards the metal back case to prevent scratching the plastic front.





Step 3
There are five retaining clips on each side of the iPod. The large iPod opening tool will be used to separate the plastic front from the metal back of the iPod.

Insert the large iPod opening tool into the left side of the iPod, with the edge of the tool pointing towards the metal back.

Gently enlarge the existing crevice by wiggling the large iPod opening tool and moving it to the left.

Continue doing so until the entire side of the iPod is loose.

You can then insert the small iPod opening tool near the Hold button. Be very careful while inserting the tool, as the display is very fragile.



Step 4
Gently glide the small iPod opening tool on the top of the display, making sure to free the retaining clips.

The other sides of the iPod should now easily come loose. If they do not, use iPod opening tools on the right side of the iPod in the same way as on the left side of the iPod.

Separate the front of the iPod from the back about an inch (or a couple of centimeters).

The iPod casing is now open, but don't completely separate the two halves just yet. Two ribbon cables are still connecting the back panel to the rest of the iPod.

Step 5
Use a small iPod opening tool to slide up the brown connector holding the orange battery ribbon cable in place. You only need to lift the brown connector up about 1-2mm to free the cable.

Make sure to slide the brown connector directly upwards. The connector is frail and will break if it is accidentally shifted to the side.

Remove the cable from the connector.

Step 6
You should now have one orange ribbon cable still attaching the front case to the back.

At this point you are able to remove and replace the blue rubber bumpers, or continue with separating the case.

Step 7
Lift up the hard drive to expose the headphone jack ribbon connector (indicated by the yellow box).

If the hard drive bumpers come loose, make sure to put them back with the notch as shown in the picture.


Step 8
With the small iPod opening tool, gently lift the brown tab of the headphone ribbon cable connector. The tab will rotate up 90 degrees, releasing the ribbon cable.

Using your fingers, pull out the headphone jack ribbon cable.

Step 9
The front and back of the iPod should now be completely separated.




Step 10 — Battery
Be careful not to damage any of the headphone or battery ribbon cables while performing this step.

Insert the small iPod opening tool in between the metal case and battery at the location illustrated by the picture.

Gently wiggle the tool while pushing it further in between the battery and back case. The adhesive holding the battery should give, allowing the battery to be removed from the rear panel.

Step 11 — Headphone Jack and Hold Switch
Be very careful when performing this step, since the orange ribbon cables can easily be broken.

Peel off the tape holding the ribbon cables in place.

Step 12
Remove the two black Phillips screws that are securing the headphone jack to the lower casing.

Step 13
Remove the following two screws:


One black Phillips screw securing the hold switch near the corner of the iPod.

One silver Phillips screw securing the other side of the hold switch.

Step 14
Lift the Hold switch free of its housing on the rear panel.

Slide the headphone jack out of its housing on the rear panel.

Lift the headphone jack and hold switch assembly out of the iPod.


Step 15
If your replacement headphone jack includes the white plastic hold switch, simply reinstall the headphone jack. If your replacement part does not include the plastic hold switch, follow the next steps to transfer the plastic hold switch to your new headphone jack.

If you're just trying to remove the rear panel, you can skip Steps 15 and 16.

Remove the single Phillips screw nearest to the hold switch.

Lift the plastic portion of the Hold switch away from the orange ribbon cable.

Ensure that the black notch lines up with the gray slider during reassembly of the switch (see picture 2).

Step 16
Use the small iPod opening tool to carefully peel the orange ribbon cable and attached black Hold switch up from the metal backing.

When re-attaching the replacement Hold switch, make sure the two small posts on the back of the switch are aligned with the two holes in the metal backing.

Saturday, September 26, 2009

Installing iPod 4th Generation or Photo Headphone Jack

Installing iPod 4th Generation or Photo Headphone Jack

No audio? Replace the headphone jack!

Tools used in this guide : T6 Torx Screwdriver , iPod Opening Tools
Parts relevant to this guide : iPod 4G 20 GB Headphone Jack , iPod 4G 40 GB Headphone Jack

Step 1 — Rear Panel
Before opening your iPod, ensure that the hold switch is in the locked position. The orange bar should be visible, indicating hold is active.


Step 2
Opening the iPod can be challenging. Don't get discouraged if it takes you a few tries before the iPod is opened.

Insert a large iPod opening tool into the seam between the plastic front and metal rear panel of the iPod, near the headphone jack. The tool's edge should point towards the metal rear panel to prevent any accidental scratching of the plastic front.

Run the tool along the top seam toward the upper left corner of the iPod. Press the tool into the corner, creating a small gap on the side of the case.

Step 3
Push the large iPod opening tool into the upper left corner of the iPod, creating a small gap along the side seam.


Step 4
There are five retaining tabs on each side of the iPod.
With the large iPod opening tool still inserted in the top seam, press a small iPod opening tool into the gap you just created.
Run the iPod opening tool down the side seam, releasing all five tabs.
It may be necessary to wiggle the tool while working your way down the seam to free all the


Step 5
Run the iPod opening tool around the lower left corner of the iPod and along the bottom seam to free the two retaining clips near the dock connector.

Step 6
Run the iPod opening tool around the lower right corner and slide it down the right side seam to free the five tabs holding the iPod together. You may be able to free the tabs by gently wiggling the front panel of the iPod.

Step 7
The iPod case is now open, but don't separate the two halves just yet. There is still an orange ribbon cable connecting the headphone jack to the logic board.
Open the case like a book with the dock connector edge at the top, and lay the rear panel next to the front half of the iPod.

Step 8
Use a plastic tool or your fingernails to carefully disconnect the orange headphone jack cable. Be sure to pull straight up on the connector, not the cable itself.

Step 9 — Headphone Jack
Remove the 2 silver T6 Torx screws from the headphone jack.

Step 10
Grasp the headphone jack board and lift it out of the iPod.

Step 11
Turn the headphone jack board over.

Use the tip of your finger or a spudger to carefully flip up the black connector holding the headphone jack cable connector in place.

Step 12
Pull the orange headphone jack cable directly out of its connector.

Thursday, September 10, 2009

Installing iPod 3rd Generation Headphone Jack

Installing iPod 3rd Generation Headphone Jack

No audio? Replace the headphone jack!

Tools used in this guide : Phillips #00 Screwdriver , Spudger , iPod Opening Tools
Parts relevant to this guide : iPod 3G 30/40 GB Headphone Jack , iPod 3G 10/15/20 GB Headphone Jack

Step 1 — Case
Before opening your iPod, ensure that the hold switch is in the locked position. The orange bar should be visible, indicating hold is active.


Step 2
Opening the case can be challenging. Do not get discouraged if it takes you a few tries before the iPod is opened.
Insert a large iPod opening tool into the seam between the plastic front and metal rear panel of the iPod, near the headphone jack. The tool's edge should point toward the metal rear panel to prevent any accidental scratching of the plastic front.
Run the tool along the top seam toward the upper left corner of the iPod.

Step 3
Push the large iPod opening tool into the upper left corner of the iPod, creating a small gap along the side seam.

Step 4
There are five retaining tabs on each side of the iPod.
With the large iPod opening tool still inserted in the top seam, press a small iPod opening tool into the gap you just created.
Run the iPod opening tool down the side seam, releasing all five tabs.
It may be necessary to wiggle the tool while working your way down the seam to free all the tabs.


Step 5
Run the iPod opening tool around the lower left corner of the iPod and along the bottom seam to free the two retaining tabs near the dock connector.
Run the tool around the lower right corner of the iPod and along the right side seam to free all five retaining tabs.
The case of the iPod should now easily come loose. Ensure all retaining tabs are free before proceeding.
Step 6
The iPod case is now open, but don't separate the two halves just yet. There is still an orange ribbon cable connecting the headphone jack to the logic board.
Open the case like a book with the dock connector at the top, and lay the rear panel next to the front half of the iPod.

Step 7
Use a plastic tool or your fingernails to carefully disconnect the orange headphone jack cable. Be sure to pull straight up on the connector, not the cable itself.

Step 8 — Headphone Jack
Remove the 3 silver Philips screws securing the headphone jack to the rear panel.

Step 9
Slide a spudger beneath the orange headphone jack cable and use it to pry the cable up from the rear panel.

Step 10
Grasp the headphone jack board and lift it out of the iPod.
When reassembling your iPod, be sure that the plastic hold switch mechanism is synced with the hold switch on the logic board. The switch on the board is a small black nub that sits in the slot on the hold switch mechanism.