PLEASE READ THIS FIRST !

Oh no! You've dropped your digital stuff. And it's out of warranty. And repair costs more than the digital stuff is worth. What to do short of tossing the digital stuff (or selling on ebay)? Well, believe it or not the average person has a good chance of diy fixing that digital stuff themselves. All they'll need for most cases is some patience, and a little background knowledge. The intent of the posts on this blog are to help provide that knowledge.

Disclaimer Warning: The following instructions are given without any warranty. They don't have to be complete or correct. Don't do any of the following steps if you're not sure of what you're doing. You could damage your digital stuffs and you WILL lose your warranty. Everything you do will be at your own risk.

Disclaimer Notice : imprtant things to know before you start taking Part your digital stuffs

Showing posts with label Board. Show all posts
Showing posts with label Board. Show all posts

Saturday, September 26, 2009

Installing iPod 4th Generation or Photo Logic Board

Installing iPod 4th Generation or Photo Display

Replace a cracked or faulty display.

Tools used in this guide : Spudger , T6 Torx Screwdriver , iPod Opening Tools
Parts relevant to this guide : iPod 4G Display

Step 1 — Rear Panel
Before opening your iPod, ensure that the hold switch is in the locked position. The orange bar should be visible, indicating hold is active.


Step 2
Opening the iPod can be challenging. Don't get discouraged if it takes you a few tries before the iPod is opened.

Insert a large iPod opening tool into the seam between the plastic front and metal rear panel of the iPod, near the headphone jack. The tool's edge should point towards the metal rear panel to prevent any accidental scratching of the plastic front.

Run the tool along the top seam toward the upper left corner of the iPod. Press the tool into the corner, creating a small gap on the side of the case.

Step 3
Push the large iPod opening tool into the upper left corner of the iPod, creating a small gap along the side seam.


Step 4
There are five retaining tabs on each side of the iPod.
With the large iPod opening tool still inserted in the top seam, press a small iPod opening tool into the gap you just created.
Run the iPod opening tool down the side seam, releasing all five tabs.
It may be necessary to wiggle the tool while working your way down the seam to free all the


Step 5
Run the iPod opening tool around the lower left corner of the iPod and along the bottom seam to free the two retaining clips near the dock connector.

Step 6
Run the iPod opening tool around the lower right corner and slide it down the right side seam to free the five tabs holding the iPod together. You may be able to free the tabs by gently wiggling the front panel of the iPod.

Step 7
The iPod case is now open, but don't separate the two halves just yet. There is still an orange ribbon cable connecting the headphone jack to the logic board.
Open the case like a book with the dock connector edge at the top, and lay the rear panel next to the front half of the iPod.

Step 8
Use a plastic tool or your fingernails to carefully disconnect the orange headphone jack cable. Be sure to pull straight up on the connector, not the cable itself.


Step 9 — Hard Drive
Grasp the hard drive with one hand and carefully disconnect the orange ribbon cable from the hard drive using your other hand.
If the cable doesn't come free easily, it may be helpful to gently wiggle the cable from side to side.

Step 10 — Hard Drive Cable
Peel up the black adhesive strip covering the hard drive ribbon cable.

Step 11
Use the tip of your finger or a spudger to carefully flip up the black connector securing the hard drive cable to the logic board.

Step 12
Pull the orange hard drive cable directly out of its connector.

Thursday, September 10, 2009

Installing iPod 3rd Generation Logic Board

Installing iPod 3rd Generation Logic Board

Your iPod's motherboard controls just about everything on the iPod.

Tools used in this guide : Spudger , T6 Torx Screwdriver , iPod Opening Tools
Parts relevant to this guide : iPod 3G Logic Board

Step 1 — Case
Before opening your iPod, ensure that the hold switch is in the locked position. The orange bar should be visible, indicating hold is active.


Step 2
Opening the case can be challenging. Do not get discouraged if it takes you a few tries before the iPod is opened.
Insert a large iPod opening tool into the seam between the plastic front and metal rear panel of the iPod, near the headphone jack. The tool's edge should point toward the metal rear panel to prevent any accidental scratching of the plastic front.
Run the tool along the top seam toward the upper left corner of the iPod.

Step 3
Push the large iPod opening tool into the upper left corner of the iPod, creating a small gap along the side seam.

Step 4
There are five retaining tabs on each side of the iPod.
With the large iPod opening tool still inserted in the top seam, press a small iPod opening tool into the gap you just created.
Run the iPod opening tool down the side seam, releasing all five tabs.
It may be necessary to wiggle the tool while working your way down the seam to free all the tabs.


Step 5
Run the iPod opening tool around the lower left corner of the iPod and along the bottom seam to free the two retaining tabs near the dock connector.
Run the tool around the lower right corner of the iPod and along the right side seam to free all five retaining tabs.
The case of the iPod should now easily come loose. Ensure all retaining tabs are free before proceeding.
Step 6
The iPod case is now open, but don't separate the two halves just yet. There is still an orange ribbon cable connecting the headphone jack to the logic board.
Open the case like a book with the dock connector at the top, and lay the rear panel next to the front half of the iPod.
Step 7
Use a plastic tool or your fingernails to carefully disconnect the orange headphone jack cable. Be sure to pull straight up on the connector, not the cable itself.

Step 8 — Battery
Lift up the hard drive with one hand and carefully disconnect the hard drive ribbon from the logic board.
Lift the hard drive out of the iPod.

Step 9
Carefully disconnect the white battery connector from the logic board. Be sure to pull only on the connector itself and not on the cables.

Step 10
Use a spudger to carefully disconnect the orange touch wheel cable from the logic board.

Step 11
Remove the 6 black T6 Torx screws securing the logic board to the front panel.

Step 12
Lift the logic board out of the iPod.
When reassembling your iPod, be sure that the plastic hold switch mechanism is synced with the hold switch on the logic board. The switch on the board is a small black nub that sits in a slot on the hold switch mechanism.

Saturday, September 5, 2009

Installing iPod 2nd Generation Logic Board

Installing iPod 2nd Generation Logic Board

Your iPod's motherboard controls just about everything on the iPod.

Tools used in this guide : T6 Torx Screwdriver , iPod Opening Tools
Parts relevant to this guide : iPod 2G Logic Board


Step 1 — Rear Panel
Before opening your iPod, ensure that the hold switch is in the locked position.

Step 2
Opening the iPod can be challenging. Don't get discouraged if it takes a few tries before the iPod is opened.

Insert a plastic iPod opening tool in the seam between the white plastic front and metal back of the iPod. Once you've inserted the tool, run it along the seam to free the five tabs holding the iPod together.

Step 3
Continue to run the opening tool along the side of the case until all five tabs have been released.

Step 4
Work around the corner of the iPod and release the two tabs holding the iPod together near the dock connector.

Step 5
Free the five tabs holding the iPod together on the other side. You may be able to free the tabs by gently wiggling the front panel of the iPod.

Step 6
Lift the rear panel away from the iPod, making sure it doesn't catch on the headphone jack.

Step 7 — Battery
Peel up the metallic tape attached to the top of the battery.

Step 8
Lift the battery up from the hard drive and lay it next the the iPod (it is still connected to the logic board).

Step 9
Carefully disconnect the orange ribbon cable from the hard drive.
If the cable doesn't come free easily, it may be helpful to gently wiggle the cable from side to side.
Lift the hard drive out of the iPod.

Step 10 — Hard Drive Cable
For the following step, you only need to move the locking bar about 2 mm. Pushing too hard or too far will damage the connector.
Loosen the connector by pulling the brown locking bar toward the hard drive cable using the tips of your fingers.

Step 11
Slide the hard drive cable out of its connector.

Step 12 — Display
Lift the blue hard drive mounting bracket out of the iPod.

Step 13
Carefully disconnect the white battery connector from the logic board. Be sure to pull only on the connector itself and not on the cables.

Step 14
Like the hard drive connector, for the following step, you only need to move the connector about 2 mm. Pushing too hard or too far will damage the connector.
Loosen the touch wheel connector by pulling the brown locking bar toward the side of the iPod using the tips of your fingers.

Step 15
Reove the 8 T6 Torx screws from the logic board.

Step 16
Lift the logic board up enough to disconnect the orange touch wheel cable.
Lift the logic board out of the iPod.

Step 17
Note the location of the four white plastic tabs securing the display to the logic board. These tabs must be released before the display can be removed.

Step 18
Use a spudger or your finger to free the four white plastic tabs indicated in the previous picture.

Step 19
Use a spudger to carefully disconnect the display ribbon cable from beneath the scroll wheel.
Lift the display off the logic board.

Step 20 — Logic Board
Logic board remains.

Congratulations!
To reassemble your device, follow these instructions in reverse order

Sunday, August 23, 2009

Installing iPod 1st Generation Logic Board

Installing iPod 1st Generation Logic Board

Your iPod's motherboard controls just about everything on the iPod.

Tools used in this guide : Spudger , T6 Torx Screwdriver , iPod Opening Tools
Parts relevant to this guide : iPod 1G 5 GB Logic Board , iPod 1G 10 GB Logic Board

Step 1 — Rear Panel
Before opening your iPod, ensure that the hold switch is in the locked position.

Step 2
Opening the iPod can be challenging. Don't get discouraged if it takes you a few tries before the iPod is opened.
Insert a plastic iPod opening tool in the seam between the white plastic front and metal back of the iPod. Once you've inserted the tool, run it along the seam to free the five tabs holding the iPod together.

Step 3
Continue to run the opening tool along the side of the case until all five tabs have been released.

Step 4
Work around the corner of the iPod and release the two tabs holding the iPod together near the dock connector.

Step 5
Free the five tabs holding the iPod together on the other side. You may be able to free the tabs by gently wiggling the front panel of the iPod.
Lift the rear panel away from the iPod.

Step 6 — Battery
Lift the battery up from the adhesive holding it to the iPod.
Lay the battery next to the iPod (it is still connected to the logic board).

Step 7
Carefully disconnect the orange ribbon cable from the hard drive.
If the cable doesn't come free easily, it may be helpful to gently wiggle the cable from side to side.
Lift the hard drive out of the iPod.

Step 8 — Display
Carefully disconnect the white battery connector from the logic board. Be sure to pull only on the connector itself and not on the cables.

Step 9
Peel up the gray rubber bumper near the hard drive ribbon to reveal the T6 Torx screw beneath.
Remove the newly revealed T6 Torx screw.

Step 10
Remove the 3 remaining T6 Torx screws from the logic board.

Step 11
Slide the logic board away from the port end of the casing and lift it out of the iPod.

Step 12
Note the location of the four white plastic tabs securing the display to the logic board. These tabs must be released before the display can be removed.

Step 13
Use a spudger or your finger to free the four white plastic tabs indicated in the previous picture.

Step 14
Use a spudger to carefully disconnect the display ribbon cable from beneath the scroll wheel.

Step 15 — Logic Board
Use a spudger to carefully disconnect the orange hard drive cable from beneath the scroll wheel.

Congratulations!
To reassemble your device, follow these instructions in reverse order