PLEASE READ THIS FIRST !

Oh no! You've dropped your digital stuff. And it's out of warranty. And repair costs more than the digital stuff is worth. What to do short of tossing the digital stuff (or selling on ebay)? Well, believe it or not the average person has a good chance of diy fixing that digital stuff themselves. All they'll need for most cases is some patience, and a little background knowledge. The intent of the posts on this blog are to help provide that knowledge.

Disclaimer Warning: The following instructions are given without any warranty. They don't have to be complete or correct. Don't do any of the following steps if you're not sure of what you're doing. You could damage your digital stuffs and you WILL lose your warranty. Everything you do will be at your own risk.

Disclaimer Notice : imprtant things to know before you start taking Part your digital stuffs

Showing posts with label Disassemble. Show all posts
Showing posts with label Disassemble. Show all posts

Wednesday, August 19, 2009

How to Disassemble IPhone 3G

How to Disassemble IPhone 3G
Tools You'll Need: Small Phillips Screw Driver , Small Flathead or exacto razor , Safe Open Tool

Ever wonder how to Disassemble your IPhone, or you really need to know how to open it because you need to replace the LCD screen because your screen cracked and. We all know it is cheaper to replace the screen than to by a new phone. Well Don't worry, here is your solution in this article you will learn how to disassemble your Iphone so you can fix it

This Article will show you how to open your IPhone3G

Remove the sim tray, use the included sim card removal tool (or a paper clip if you've lost the tool.)

Holding your device on end you will notice two small screws on either side of the dock. These screws must be removed in order to open the case.

Insert a small thin tool between the chrome ring and front panel glass directly above one of the screw holes. You will need to exert a small amount of pressure to separate the display from the back panel

Lift the panel up from the dock end being careful not to tear or break any ribbons connected near the other end.

Unplug ribbons 1 and 2 by lifting them from the main board. Under ribbon 2 you will need to find and unclip ribbon 3, then carefully remove the display assembly.

Remove the seven screws circled in red. Note: One screw is located under the DO NOT REMOVE sticker.

Unplug ribbon 4.

Lift the mother board out taking note of the camera which is still connected to the underside of the board. You will need to unplug the ribbon circled in red.

Place the mother board to the side

Use the attached tab to pull up on the battery, there is a mild adhesive on the back side, so it will take a bit of force.

Remove the screw circled in red.

Carefully remove the camera

Remove the nine screws circled in red.

Remove the headphone jack and attached flex cable.

Remove the speaker assembly which also contains the dock connector, antennae and home button as well.

Remove the 2 screws circled in red.

Place the ######## assembly to the side

Remove the 2 screws circled in red. You will find 3 screws on the opposite side which must be removed as well.

Lift the LCD free from the front panel glass.

Pictured is every component inside the iPhone 3G.You did it!

Friday, August 14, 2009

Sony Ericsson K750i LCD replacement

Sony Ericsson K750i LCD replacement
Tools required:
plastic shim such as a guitar plectrum, Phillips screwdriver and T6 screwdriver

Remove the battery cover, battery and sim card. Unscrew the 2 x Philips and the 2 x T6 torx screws you see. Use the shim to skim around the edges of the back cover, whilst gently lifting the cover to prise and release the clips (as pictured below).



Below is how the phone will look once you have removed the front cover. Now remove the keypad

Next, remove the plate below the keypad and black plastic backing. Lever this part gently from the left side of the phone as pictured. You’ll see a connector on the right hand side of the phone (circled). Using a small flat screwdriver, unplug it and lift away the plate.

WARNING: There are 2 tiny brass-like clips on the black plastic backing plate (circled). DO NOT lose these! In fact, try not to even dislodge them from the plate.

To replace the LCD, remove the 2 x T6 torx screws from the top of the screen. Unplug the screen connector from the PCB (circled in yellow).

Then, easing it over the joystick, lift the screen free. Replace with the new screen. Reverse the procedure for disassembly and it's finished.

Thursday, August 13, 2009

Disassemble Sony VAIO PCG-NV190 Laptop

Disassemble Sony VAIO PCG-NV190 Laptop
Tools required: Set of slotted/phillips screwdrivers , Needle Nose Pliers , Scratch Awl , 3/16 Nutdriver , Torx 8 Screwdriver , Guitar pick (heavy) , Container for screws.

Step 1

Raise the Assy Hood Keyboard – the piece just above the actual keyboard that contains the speakers, power switch, etc.

The Assy Hood Keyboard is held in place by four posts that are spaced along the edge just above the actual keyboard. Spring clamps hold the posts. I gently pried the Assy Hood Keyboard up with small screwdrivers at each end (see arrows in the picture) and then worked my way towards the center. Take care in doing this so as not to break the Assy Hood Keyboard.

Next gently rotate the Assy Hood Keyboard up and towards the top of the laptop. The Assy Hood Keyboard is attached to the motherboard by a small ribbon cable. Depending on what you need to do inside the case you can either disconnect the Assy Hood Keyboard and put it aside or leave it attached but laid out of the way. To disconnect the Assy Hood Keyboard ribbon cable pull up on the blue spacer that holds the ribbon cable in the motherboard connector. The ribbon cable should come out of the connector when the blue spacer comes out. Be sure to save the blue spacer for when you are connecting the Assy Hood Keyboard back to the motherboard.

Step 2

Disconnect the actual keyboard – the piece with all the character keys.

The actual keyboard is attached with a screw just above the keyboard’s center (see arrow in the next picture). After removing this screw you can gentle rotate the keyboard toward you – i.e. towards the bottom of the laptop. The keyboard is connected to the motherboard by a ribbon cable

Depending on what you need to do inside the case you can either disconnect the keyboard and put it aside or leave it connected. You disconnect the keyboard ribbon cable by gently pulling up on the ends of the motherboard connector (see next picture). However the motherboard connector does not come apart in the process so do not attempt to pull the connector release mechanism to hard – just enough to raise it a short ways which should release the ribbon cable.

Step 3

Remove the cover plate with cooling fan attached.

Sorry that the next picture isn’t very clear but it is too late to take another one. However you should be able to make out everything needed to remove the cover plate. First disconnect the fan from the motherboard by pulling up on the socket on the end of the fan wires (red arrow). Next unscrew the nine screws that hold the plate. Each screw is identified by an arrow inscribed in the plate (example in the red circle). Two of the screws are long and are identified by L1 and L2 inscribed in the plate (highlighted by an L1 and L2 in red). Three of the screws are at the bottom of wells identified by D1, D2, and D3 in red.

When the cover plate has been removed you will have access too much of the motherboard as shown in the next picture. I was able to accomplish my objective at this point so I did not do any further disassemble.

Hope this helps.